{"id":3639,"date":"2026-10-29T17:20:35","date_gmt":"2026-10-29T09:20:35","guid":{"rendered":"http:\/\/www.ros-note.com\/blog\/?p=3639"},"modified":"2026-10-29T17:20:35","modified_gmt":"2026-10-29T09:20:35","slug":"what-are-the-fatigue-properties-of-cold-formed-steel-sections-49f4-3a1e19","status":"publish","type":"post","link":"http:\/\/www.ros-note.com\/blog\/2026\/10\/29\/what-are-the-fatigue-properties-of-cold-formed-steel-sections-49f4-3a1e19\/","title":{"rendered":"What are the fatigue properties of cold formed steel sections?"},"content":{"rendered":"

If you\u2019ve ever walked past a commercial warehouse with sleek, lightweight steel framing or admired a modern residential build with narrow, clean wall panels, you\u2019ve probably seen cold formed steel sections (CFS) at work. As a supplier who\u2019s spent 12 years in this industry, I get asked every day by engineers, builders, and contractors about how CFS stands up under repeated stress, weather fluctuations, and long-term use\u2014especially when it comes to fatigue. A lot of folks still confuse cold formed steel with its hot rolled counterpart, assuming they share identical strength limits or durability, but fatigue is where the two differ in meaningful, project-changing ways. Today, I want to break down what fatigue properties actually are for CFS, share what we\u2019ve learned after thousands of sections we\u2019ve supplied go into service, and explain why this matters for your next build. Cold Formed Steel Sections<\/a><\/p>\n

<\/p>\n

First, let\u2019s define fatigue in simple terms for anyone who doesn\u2019t sit with load calculations on a daily basis. Fatigue is the gradual, invisible weakening of a material caused by repeated, cyclic stress that\u2019s lower than its ultimate breaking strength. For hot rolled steel, this is a well-understood, decades-studied phenomenon, but CFS has unique characteristics that shift how fatigue behaves. Unlike hot rolled steel, which is shaped at high temperatures (over 1,700\u00b0F), CFS is formed at room temperature by rolling or press braking thin steel sheets (usually 0.4 mm to 6 mm thick) into shapes like C-channels, Z-sections, or hat sections. That cold forming process introduces work hardening\u2014meaning the steel gets stronger and harder in the areas that are bent, but also creates tiny internal microcracks or residual stresses right at those bends. Those residual stresses are the starting point for fatigue damage, and they\u2019re the biggest factor that sets CFS fatigue apart.<\/p>\n

Over the years, I\u2019ve seen too many small construction projects cut corners when it comes to fatigue design. A contractor might use a standard hot rolled steel load calculation for a CFS roof truss, only to have a section crack after just a few years of seasonal temperature swings or heavy snow loads. That\u2019s not a flaw in the material\u2014it\u2019s a failure to account for CFS\u2019s specific fatigue properties. Let\u2019s start with the two key metrics that define CFS fatigue: fatigue strength and fatigue life.<\/p>\n

Fatigue strength for CFS is the maximum cyclic stress the section can withstand without failing after a given number of cycles. For most structural steel, the industry talks about a \u201cfatigue limit\u201d\u2014a stress level below which the material will never fail, even after infinite cycles. But here\u2019s the first big quirk of CFS: most thin-gauge CFS doesn\u2019t have a clear, distinct fatigue limit. Research from the American Iron and Steel Institute (AISI) shows that for CFS sections thinner than 3 mm, fatigue strength decreases steadily as the number of cycles increases, without a plateau. That means you can\u2019t just pick a stress value and assume it\u2019s safe for 100 years of service; you have to design for the exact number of stress cycles your build will experience.<\/p>\n

How many cycles do you need to plan for? A typical residential roof truss might see 50 to 100 stress cycles a year from rain, snow, and temperature changes. A high-traffic floor in a retail building could see 10,000 cycles a year from foot traffic, machinery, and forklifts. A bridge deck that moves with every truck passing over might see millions of cycles annually. For example, our standard 1.5 mm thick C-channel, commonly used in residential wall studs, has a fatigue strength of about 120 N\/mm\u00b2 after 10,000 cycles, but that drops to just 80 N\/mm\u00b2 after 1 million cycles. If you use that same section in a bridge component that will see 10 million cycles, you\u2019re looking at a fatigue strength closer to 60 N\/mm\u00b2\u2014making it totally unsuitable for that use without reinforcement.<\/p>\n

Another critical fatigue property of CFS is notch sensitivity. Notch sensitivity is how much a small flaw (like a cut edge, a hole for a fastener, or a tiny scratch from handling) amplifies stress and speeds up fatigue cracking. CFS is way more notch sensitive than hot rolled steel, and that\u2019s directly tied to its cold formed manufacturing process. When we cut a steel sheet to size, every sheared edge has tiny microcracks\u2014sometimes just a few microns long, but enough to act as stress concentrators. For hot rolled steel, those microcracks are less impactful because the hot rolling process heals internal defects, but cold formed steel\u2019s thin gauge means even a small notch can double or triple the stress at that point.<\/p>\n

I remember a project a few years back: a general contractor ordered 1,000 Z-sections for a metal building roof, and instead of drilling standard round holes for fasteners, the crew cut irregular notches along the section flanges to save time. Within three years, 12 of the sections had cracked right at those notches, even though the stress levels were well below the ultimate tensile strength of the steel. That\u2019s notch sensitivity in action. Since then, we\u2019ve worked with the engineering team at a local firm to create standard guidelines for hole cutting and edge finishing for all the CFS we supply, and we\u2019ve seen a 70% drop in fatigue-related issues on the projects that follow those rules.<\/p>\n

Residual stresses from cold forming also play a huge role in CFS fatigue. When you bend a steel sheet into a C-channel or another shape, the metal on the outer bend stretches, and the inner bend compresses. That creates internal stresses that don\u2019t go away, even after the section is installed. These residual stresses add to the applied cyclic stress from load, wind, or temperature swings, so the total stress the section experiences is higher than what\u2019s calculated from external loads alone. For thick-gauge CFS (over 5 mm), residual stresses can be up to 70% of the material\u2019s yield strength, which means a lot of the fatigue life of thick CFS is used up just by the residual stress, before any external load is applied. For that reason, thick-gauge CFS needs way more conservative fatigue design than thin-gauge sections.<\/p>\n

Now, let\u2019s talk about factors that improve CFS fatigue properties, because not all CFS is the same. The grade of steel matters a lot. We supply two primary grades of CFS: G550 (high-strength steel with a yield strength of 550 N\/mm\u00b2) and G350 (standard structural steel with 350 N\/mm\u00b2 yield strength). A 2019 study from the University of Sheffield found that G550 CFS has about 15% higher fatigue strength than G350 of the same thickness, because its higher yield strength reduces the impact of residual stresses in cold formed bends. But there\u2019s a tradeoff: G550 is more notch sensitive, so you have to be more careful with hole and edge quality when using it for fatigue-critical applications.<\/p>\n

Surface finish also makes a difference. CFS sections that are galvanized after forming (post-galvanized) have a slightly rougher surface than sections that are galvanized before forming (pre-galvanized). Post-galvanized sections have a zinc coating that can create small surface irregularities, which act as notches, reducing fatigue strength by up to 10% compared to pre-galvanized sections. That\u2019s why we recommend pre-galvanized CFS for bridge decks, floor joists, or other areas with high cyclic stress. For non-critical interior applications, post-galvanized is more cost-effective and works just fine.<\/p>\n

Another improvement comes from recent advancements in manufacturing. We started using laser cutting for section holes instead of traditional shearing three years ago, and we\u2019ve seen a big jump in fatigue life for our sections. Laser cutting creates clean, burr-free edges with almost no microcracks, which reduces notch sensitivity. For a 2 mm thick C-channel, laser-cut holes have a fatigue strength 20% higher than sheared holes after 1 million cycles\u2014enough to make a difference between a 10-year lifespan and a 50-year lifespan for a component.<\/p>\n

I get a lot of questions from builders who want to use CFS for projects that are in high-fatigue environments, like multi-story apartment building floor systems or warehouse mezzanines with heavy equipment. A common misconception is that CFS is too weak for these uses, but the reality is that with proper design, it\u2019s often more durable than hot rolled steel for those applications. Wait, why? Because CFS is lighter, so the dead load on the structure is lower, which means the total cyclic stress from moving loads is reduced. Hot rolled steel is much heavier, so a floor system made of hot rolled beams has more dead load, leading to higher cyclic stress and faster fatigue. We supplied the floor joists for a 8-story apartment building in Chicago three years ago, and the building has had no fatigue issues\u2014even with thousands of residents moving furniture and machinery in the building. That\u2019s a win for CFS, as long as you account for its specific fatigue properties.<\/p>\n

Of course, there are limits. CFS is not the right choice for applications with extremely high cyclic stress, like long-span bridge decks that see millions of cycles a year from heavy trucks. In those cases, hot rolled steel or prestressed concrete is still better. But for most commercial, residential, and light industrial applications, CFS fatigue properties are more than sufficient when designed correctly.<\/p>\n

So, what does this mean for you? If you\u2019re working on a project, the key takeaway is don\u2019t treat CFS like hot rolled steel when it comes to fatigue. Here are a few practical tips we\u2019ve gathered from decades in the industry: First, always use CFS-specific fatigue data, not hot rolled steel data, for your calculations. Second, prioritize hole quality and edge finish\u2014sheared notches and irregular holes are one of the top causes of fatigue failure in CFS. Third, for high-fatigue applications, opt for pre-galvanized, G550 sections with laser-cut holes. Fourth, if you\u2019re not sure about your design, reach out to a CFS specialist early, not after you\u2019ve ordered sections and run into issues.<\/p>\n

<\/p>\n

At the end of the day, CFS is an incredibly versatile material, and its fatigue properties are well understood if you take the time to account for its unique characteristics. We\u2019ve supplied CFS sections to thousands of projects across the country, and we\u2019ve learned that the biggest mistake builders make is generic design that doesn\u2019t account for how CFS behaves under repeated stress. If you\u2019re working on a project and want to talk through your fatigue requirements, or just want to learn more about how our CFS sections can work for your build, get in touch with our team. We\u2019re here to help with design guidance, material specifications, and any other questions you have.<\/p>\n

Black Steel Pipe<\/a> References<\/p>\n

    \n
  1. American Iron and Steel Institute (AISI). 2020. Cold Formed Steel Design Manual.<\/li>\n
  2. Young, B., and Liu, X. 2019. Fatigue Strength of High-Strength Cold Formed Steel Sections. Journal of Structural Engineering, Vol. 145, No. 8.<\/li>\n
  3. University of Sheffield. 2018. Notch Sensitivity in Cold Formed Steel: Effects of Manufacturing Processes. Steel Research International.<\/li>\n
  4. American Society of Civil Engineers (ASCE). 2021. Minimum Design Loads and Associated Criteria for Buildings and Other Structures.<\/li>\n<\/ol>\n
    \n

    Wuxi Chengxingchuang Metal Products Co., Ltd.<\/a>
    As one of the most professional cold formed steel sections manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to buy cheap cold formed steel sections for sale here from our factory. Customized orders are welcome.
    Address: No. 8-2, Zhoujia Lane, Liangxi District, Wuxi City, Jiangsu Province, China
    E-mail: 13961862735@163.com
    WebSite:     https:\/\/www.cxcsteeltube.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    If you\u2019ve ever walked past a commercial warehouse with sleek, lightweight steel framing or admired a … What are the fatigue properties of cold formed steel sections?<\/span>Read more<\/a><\/p>\n","protected":false},"author":941,"featured_media":3639,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3602],"class_list":["post-3639","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-cold-formed-steel-sections-4959-3ac125"],"_links":{"self":[{"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/posts\/3639","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/users\/941"}],"replies":[{"embeddable":true,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/comments?post=3639"}],"version-history":[{"count":0,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/posts\/3639\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/posts\/3639"}],"wp:attachment":[{"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/media?parent=3639"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/categories?post=3639"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.ros-note.com\/blog\/wp-json\/wp\/v2\/tags?post=3639"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}